Serie BL192

Prodotti Serie BL192

DATI TECNICI – serie BL192

  • Motoriduttore Brushless con elettronica integrata.
  • Motore brushless 3 fasi 12 poli con 3 sensori di Hall.
  • Albero di uscita supportato da due cuscinetti a sfera.
  • Massimo carico radiale: 200N (a 10mm dalla flangia di fissaggio)
  • Massimo carico assiale: 100N.
  • Temperatura di esercizio: -10 °C/+50 °C.
  • Peso approssimativo: 320/420g.

Valori tipici a temperatura ambiente +20°
Tolleranza +/- 10%

_

Disegno Tecnico

Rating
N. °ItemSpecificationNote
1 Rated voltage DC 24V
2 Min. operating voltage DC 16V
3 Max. operating voltage DC 26.4V
4 Type 3 phases 12 poles brushless motor with 3 hall sensor
5 Rotating direction CW/CCW
6 Bearing type Sleeve bearing
7 Motor posture Horizontal
8 Motor mass 145g Typ.
Electrical characteristics (temp. 20+/-5 °C, relative humidity 80% max)
N. °ItemSpecificationNote
1 Dielectric strength AC 600V 1 sec 1mA Check between all shorted terminals and motor cover
2 Insulation strength DC 500V 10MΩ Min
3 No load current 0.36A Max DC 24V
4 No load speed 5000 +/- 15% RPM DC 24V
Temperature ratings
N. °ItemSpecificationNote
1 Operating ambient conditions Dry bulb temp: -10 +50 °C Relative humidity: 0 - 90%
2 Max permissive coil temp. 115 °C
3 Max permissive IC surface temp. 110 °C
4 Max permissive FET surface temp. 110 °C
5 Max Transistor Temperature 110 °C
6 Max permissive lead wire temp. 105 °C
7 Max permissive bearing temp. 90 °C
Circuit protection
N. °ItemSpecificationNote
1 Current limit 3A Typ. Using PWM
2 Thermal shutdown 175 °C +/-30 °C There is no guarantee of proper operation when thermal shutdown motor is reused.
3 Motor lock protection 2 sec Typ. When the motor locks, the motor current is automatically cut off within the defined time. The motor restarts by power supply reset.
Interface
Pin No.Signal nameI/OSpecificationNote
1 VM IN DC 24V +/- 10% Power supply
2 GND IN Ground
3 CW/CCW IN
Input voltage range 0-5V High CW
Low CCW
VIH 2.0V Min
VIL 1.0V Max
4 FG OUT
VOH 6V Max You need to pull up for FG terminal so that the terminal is open drain output.
VOL 0.6V Max
Max rating of FG sink current 3mA
Number of FG output pulse 6 Pulse/round
5 PWM IN
Input voltage range 0-5V High motor ON
Low motor OFF
VIH 2.5V Min
VIL 1.0V Max
Max PWM input frequency 40 kHz Recommended between 15 to 25 kHz
6 START/STOP IN
Input voltage range 0-5V High motor Start
Low motor Stop
VIH 2.0V Min
VIL 1.0V Max

You should connect a Schottky Barrier Diode between each signal line and the ground to prevent lc from being damaged. We recommend to the connect 47uF capacitor between 5V to GND for protecting from filter actions by electrical noises. Do not change CW/CCW input until motor has stopped completely, if you change the CW/CCW signal during motor running, the motor may have some damage or be destroyed.

TipoTensione nominaleLunghezzaRapporto di riduzioneCoppia nominaleVelocitàCorrentePotenza elettrica
Senza caricoA coppia nominaleSenza caricoA coppia nominale
vmmNcmrpmmAW
BL1922432467,53,66151360880<350115027,6
BL1922452467,55201000660<350115027,6
BL19224132474,513,4445370255<350110026,4
BL19224182474,518,3360275190<350110026,4
BL19224252474,52590210138<350110026,4
BL19224492481,549,2916010268<350110026,4
BL19224672481,567,222207350<350110026,4
BL19224912481,591,662705437<350105025,2
BL192241252481,51253004030<35095022,8
BL192241802488,5180,752202924<35063015,12
BL192242462488,5246,483002017<35067016,08
BL192243362488,5336,113001513<35056013,44
BL192244582488,5458,333001110<35053012,72
BL192246252488,562530087,5<35043010,32

Download Area

Serie BL192
file-2
Scheda tecnica Download
×